This article describes the Network Settings page of the Datto BCDR device GUI.
- Datto ALTO
- Datto SIRIS
Network settings for Datto BCDR devices are configured and administered on the Device GUI's Network Settings page.
Accessing network settings
1. In the Datto device GUI, click the Configure tab, Then, click Networking in the drop-down menu.
Figure 1: The Datto device GUI (click to enlarge)
This table shows the status of connections to the Datto device's Ethernet ports.
Figure 2: Networking Status (click to enlarge)
This table provides a summary of the following connectivity stats:
- Ping size: MTU packet size. Datto appliances require a 1500 byte MTU. See the this article for more information.
- Off-site Storage and Connection to off-site Storage: the status of the device's connection to the Datto Cloud.
- Port 22 outbound: allows SSH access to the device.
- Device web 443: reports connectivity to device.dattobackup.com. This port must be open for the device to function properly.
- Port 80 outbound: allows connections to the device via HTTP. This port must be open for the device to function properly.
- Port 443 outbound: allows connections to the device via HTTPS. This port must be open for the device to function properly.
- BMC: reports connectivity to Datto's Bare Metal Restore servers.
- Port 21: reports connectivity to Datto's Speedtest server.
- Diagnostic services: refers to the connection between the device and Datto's monitoring servers
- Heartbeat: reports connectivity to Datto's checkin servers.
- Package servers: reports connectivity to Datto's software update servers.
- DLOG: reports connectivity to Datto's Filebeat servers
- Resolve device hostname: queries the configured DNS Server to see if the device's hostname resolves.
- DLT: reports connectivity to Datto's Ubuntu package server mirror.
- Time services: reports connectivity to NTP servers.
To check connectivity from your Datto device to the network, click the Run Outbound Connectivity Check button.
Figure 3: Connectivity Status (click to enlarge)
This section lets you configure the NICs on your Datto appliance. You can use any NIC as the primary NIC, and configure the additional NICs for specific purposes. See Device Auxiliary NIC Settings to learn more about auxiliary NIC uses.
- IP Mode lets you switch each NIC between DHCP and static. Datto recommends leaving leave the IP Mode set to DHCP. If your network requires a static IP address, you can configure one here.
If the IP Mode is set to Static, you will be able to set the IP Address, Netmask, and Gateway values. You cannot change network settings while DHCP is checked.
- Jumbo Frames: Click this radio button to enable Jumbo Frames functionality on a per-NIC basis. Jumbo Frames are Ethernet frames that transmit at greater than the standard maximum transmission unit (MTU) of 1,500 bytes. With Jumbo Frames enabled, your Datto appliance will attempt to generate Ethernet frames with an MTU of 9,000 bytes.
Both the switch and the protected machine must support Jumbo Frames, and have this feature turned on. Your environment must also employ gigabit networking. Support for Jumbo Frames and their maximum transmission unit may vary from vendor to vendor.
- Bonded interfaces: This feature lets you create a bonded NIC configuration. For more information, see Enabling NIC Bonding.
Figure 4: IP settings (click to enlarge)
Datto recommends providing at least one remote DNS server (such as Google's 188.8.131.52.). If a disaster occurs to the local DNS Server the device will be able to use the remote DNS Server to resolve dattobackup.com so you can perform a remote recovery.
In a domain environment, you can enter the FQDN for the DNS Search Domain so the Datto device can protect machines using DHCP by their hostnames.
Figure 5: Server 1 set to local DNS & Server 2 set to public DNS (click to enlarge)
This sets the hostname of the Datto device.
Datto recommends using a hostname for the Datto device that helps identify the customer, company, or network on which it is deployed. This is because this Datto device's hostname appears in the Datto Partner Portal's Device List.
Figure 6: Hostname change interface (click to enlarge)
Windows Networking - Workgroup Mode
This optional field is where the Datto device can be joined to a domain.
Note:The option to join Datto devices to a local domain was provided specifically for deployments where the NAS feature with domain authentication credentials will be used.
Tip:Datto suggests leaving your appliance in Workgroup mode if its NAS feature is not in use. This helps prevent the device from being dependent on the local domain during disasters.
Figure 7: Windows Networking - Workgroup Mode interface
Steps to join a Datto device to the local domain
- Enter in the local domain with domain administrator level credentials.
Note:The Optional Password Server field is for use with local RSA servers.
- Next, click the Join Domain button to join the Datto to the local domain.
Figure 8: Domain-joining mode
For SIRIS 3 devices with IPMI, you can change the device's IPMI settings through the user interface.
Figure 9: IPMI Settings (on supported devices)
These settings allow you enable or disable IPMI, configure the IPMI network settings, and change the passwords for admin users. See How Do I Access IPMI on SIRIS 3 devices Remotely From the Partner Portal? to learn more about remote management options for compatible Datto appliances.