ALERT: Datto Drive Cloud service will no longer be available as of July 1, 2019. For more information, see our end-of-life article. If you'd like to migrate your data to Datto Workplace, see our migration guide.
To learn how to download your Datto Drive Cloud data, please visit this article.

IPMI on SIRIS 3 and SIRIS 3X Professional



This article explains how to configure, access, and use the Aptio Setup Utility to access a SIRIS 3 Professional or SIRIS 3 X Professional through IPMI.


  • Datto SIRIS 3 Professional
  • Datto SIRIS 3 X Professional


Configure IPMI

Before you can access the Datto appliance's remote management interface, you will need to configure IPMI. See the GUI: Network Settings article for more information.

If you are unable to configure IPMI via the GUI, you can perform the following steps.

Set up the IP Address

To configure IP and MAC addresses, enter the Aptio Setup Utility by pressing F2 on boot.

1. Enter the BIOS password. You will then see the main page of the setup utility, as shown in Figure 1.

Figure 1: Aptio Setup Utility

2. Select Server Mgmt, and press Enter. From there, select BMC Network Configuration as shown in Figure 2.

Figure 2: IPMI Configuration screen

3. Select Manual setting IPMI LAN, and press Enter. This will give you the ability to change IP settings and toggle Static and DHCP services.

Figure 3: BMC Network Configuration

4. We recommend that you provide a static, reserved IP address for the management console.

Figure 4: Static IP Address

5. Hit F10 to save and exit.

Login to IPMI

Now that we have an IP address defined for the dedicated IPMI port, we can now connect to the IPMI web interface locally to manage your Datto appliance.

  1. Go to a computer that is connected to the same LAN as the Datto, and open a web browser.

  2. In the address bar of your web browser, enter the IP address you configured for the IPMI port.

  3. When you get the login page, enter your credentials:
    • Username: admin
    • Contact Tech Support for the password

      Figure 5 - IPMI Login

You are now remotely logged into the Datto device's management interface. Here you can control power, monitor system health, and add virtual media such as CD, DVD ROM, floppy disk images.

Change User Password

For security reasons, we recommend that you change your password right away. Follow these steps to do so:

  1. From the top drop-down menu, hover over Configuration, and select Users.

    Figure 6 - Configuration Menu

  2. Select the admin user, and then click Modify User.

    Figure 7 - User Management

  3. Select the Change Password check-box, and enter your new password. Then, click Modify.

    Figure 8 - Modify User

  4. When you get the message Modified user successfully, click OK.
  5. Once you've changed the administrator password, disable the anonymous user. To do so, go through the same process to modify the anonymous user, and un-check the box that says Enable. Click the Modify button to finish the process.
  6. If there are any extra administrator accounts, disable them as well.

Launching Remote Console

The Aptio Setup Utility allows you to launch a remote console session into the Datto appliance. To use this console, you must have Java installed on your workstation. To launch a session, follow these steps:

  1. Click the Remote Control tab. Then, click Console Redirection, as shown in Figure 9.

    Figure 9 - Remote Control Menu

  2. Click the Java Console button.

    Figure 10 - Console Redirection

  3. You will be prompted with a few warnings about the downloaded file. Click to download and keep the file.

    Figure 11 - Keep the file

  4. Click the jviewer file to launch the console. You will then see the console window as shown in Figure 12.

    Figure 12 - JViewer Console Window

Accessing the Datto Appliance Command Line

Troubleshooting tip: the JViewer Console Window is a Java applet. If there are any issues with the following steps, start by troubleshooting your Java installation.

If you would like to access the command line of the Datto appliance through IPMI, follow these steps:

  1. Go into the Keyboard Layout menu, and click SoftKeyboard. Choose the layout you wish to use.

    Figure 13 - Soft Keyboard

  2. Click these keys: ctrl + alt + F1

    Figure 14 - ctrl + alt + F1

  3. You will then see the Datto OS command line.

    Figure 15 - Command Line

  4. When you are finished using the command line, click ctrl + alt + F8 to get back to the GUI.

Server Power Control

Another great feature of the Setup Utility is the ability to control power options, even if the device is fully powered down. To access this feature, click the Power menu, as shown in Figure 13.

Figure  - Power Control

The power control options are as follows:

  • Reset Server: reboots the server without fully powering down
  • Immediate Shutdown: forces an immediate shutdown
  • Orderly Shutdown: shuts down the server gracefully
  • Power On Server: powers on the server
  • Power Cycle Server: powers down the server completely and then powers it back on

Additional Resources

Was this article helpful?

2 out of 3 found this helpful

You must sign in before voting on this article.

Want to talk about it? Have a feature request?

Head on over to our Community Forum or get live help.