We have identified an issue with the 2.0.9 version of the Datto Windows Agent. An auto-upgrade hotfix is available. Further information is available at the Datto Service Status page.

Legacy Open Mesh: Switch firmware release notes

Follow

Topic

This article lists firmware release notes for Datto Switches.

Environment

  • Datto Switches

Description

1.03.24 - Released October 15, 2018

Bug Fixes

  • Resolved an issue where wrong configurations caused a memory leak
  • Resolved an issue for OMS48 switches that caused check-ins to miss scheduling

1.03.19 - Released July 11, 2018

New Features  - CloudTrax support coming soon

  • Auto Voice VLAN: Added LLDP-MED functionality that allows a switch to broadcast the Voice VLAN configuration
  • SNMP Trap: Added functionality that allows a switch to send SNMP alert messages
  • Jumbo Frames: Added functionality that allows a switch to send Ethernet frames larger than 1500 bytes
  • LED Dark Mode: Added functionality that allows a port to operate with its LED disabled

Improvements

  • Added functionality that lets the connection keeper use TCP keep-alive messages.
  • Updated certificate for cloud connections

Bug Fixes

  • Corrected the Jumbo Frame range utilized by switches
  • Resolved an issue where SNMP versions were reversed
  • Resolved an issue where a fiber port failed to operate under dark mode
  • Reduced the number of times NTP server is called to once per hour
  • (S24v3 only) - Resolved an issue that prevented the 10GB fiber port from achieving a link
  • (S24v3 only) - Fixed an issue where a 10GB SFP module could not properly trunk
  • (S24v3 only) - Resolved an issue that prevented port speed settings from being saved
  • (S24v3 only) - Fixed an issue where control packets could not trap to the CPU on port 26

1.03.15

S24v3 initial firmware release

1.03.11 - Released January 30, 2018

Bug Fixes

  • Get time from fallback CloudTrax server when DNS fails

1.03.09 - Released September 11, 2017

Bug Fixes

  • Improves reliability of check-in if using the wrong DNS

1.03.07 - Released August 2, 2017

New Features

  • Supports new line of switches S8-L and S24-L

Bug Fixes

  • Updated local SSL certificates to ensure continued check-in with CloudTrax into the future

1.03.05 - Released July 11, 2017

New Features

  • LLDP (not LLDP-MED)
  • Diagnostic features (Cable Test / Ping / Traceroute)

Bug Fixes

  • FIX: Switch could hang when setting a rate limit on a port

1.02.07 - Released April 12, 2017

Bug Fixes

  • Addresses a condition where the Switch stops checking in
  • Improvements to upgrade process and install validation

1.02.05  - Released March 23, 2017

New Features

    • Auto-detect uplink port
    • Port (and overall) forwarding table 
    • Add protection for PVID and Untagged VLANs, once we can autodetect uplink
    • Security:
      • MAC ACL/ ACE
      • IPv4 ACL/ ACE
      • Port Isolation
    • Bytes per port
      • Data (all tx and rx counters)
      • Graph 
    • QoS
      • Enable/ disable
      • DSCP -> CoS mapping
      • CoS -> Switch queue mapping
      • Trust incoming classification or set own
    • Voice VLANs
      • Enable/ Disable
      • VLAN ID
      • OUI list: Default and add new ones
      • Enable disable voice VLAN
      • Set CoS mode 

1.01.01  - Released November 14, 2016

New Features

  • Spanning Tree Protocol (STP)
  • IGMP Snooping
  • PoE Reset (instant)
  • Link Speed and Mode
  • Rate Limiting (Tx/Rx)
  • Flow Control
  • Link Aggregation
  • Port Mirroring
  • PVID (Native VLAN) and Untagged VLANs 

1.00.02 Released October 11, 2016

New Features

  • Ability to view per-port PoE consumption
  • Dynamic port controls from switch image within the switch pane:
    • Identify and click through to Open Mesh AP, when connected directly
    • Identify and list devices in the port forwarding table, when not directly connected to an OM AP 

1.00.00 - Released October 1, 2016

New Features

  • Cloud management and configuration via CloudTrax
  • Configurable scheduled firmware upgrades, by switch model
  • Monitoring Features:
    • Total Power
    • Current Usage/ Available Power
    • Device Name
    • MAC Address
    • IP Address
    • Gateway IP Address
    • Total and Active Ports (e.g., 2/10)
    • Firmware version
    • Uptime
    • PoE Budget
  • Configuration Features:
    • Enable/ Disable PoE
    • PoE Type: Manual or Auto
    • Priority (when Type set to Auto)
    • Power limit (when the type is set to manual)
    • Number and Description
    • Status
    • Enable/ Disable Link
    • Allowed VLANs
    • PoE configuration
    • SNMP configuration (read-only)
    • Per Port Configuration
  • Local Management (Web GUI, telnet, SSH): Disabled on first cloud check-in, to prevent configuration conflicts with CloudTrax.

Was this article helpful?

0 out of 0 found this helpful

You must sign in before voting on this article.

Want to talk about it? Have a feature request?

Head on over to our Datto Community Forum or the Datto Community Online.

For more Business Management resources, see the Datto RMM Online Help and the Autotask PSA Online Help .

Still have questions? Get live help.

Datto Homepage